Skip to main content

How To Make HC-05 Bluetooth Controlled Car With Arduino UNO|Topped With Fun(With Code And Diagram)




Circuit Diagram:-

Code:-
#include <AFMotor.h>

//initialising motors pin
AF_DCMotor motor1(1, MOTOR12_1KHZ); 
AF_DCMotor motor2(2, MOTOR12_1KHZ); 
AF_DCMotor motor3(3, MOTOR34_1KHZ);
AF_DCMotor motor4(4, MOTOR34_1KHZ);

char command; 

void setup() 
{       
  Serial.begin(9600);  //Set the baud rate to your Bluetooth module.
}

void loop(){
  if(Serial.available() > 0){ 
    command = Serial.read(); 
    Stop(); //initialize with motors stoped
    //Change pin mode only if new command is different from previous.   
    //Serial.println(command);
    switch(command){
    case 'F':  
      forward();
      break;
    case 'B':  
       back();
      break;
    case 'L':  
      left();
      break;
    case 'R':
      right();
      break;
    }
  } 
}

void forward()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(FORWARD); //rotate the motor clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(FORWARD); //rotate the motor clockwise
  motor3.setSpeed(255);//Define maximum velocity
  motor3.run(FORWARD); //rotate the motor clockwise
  motor4.setSpeed(255);//Define maximum velocity
  motor4.run(FORWARD); //rotate the motor clockwise
}

void back()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(BACKWARD); //rotate the motor anti-clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(BACKWARD); //rotate the motor anti-clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(BACKWARD); //rotate the motor anti-clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(BACKWARD); //rotate the motor anti-clockwise
}

void left()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(BACKWARD); //rotate the motor anti-clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(BACKWARD); //rotate the motor anti-clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(FORWARD);  //rotate the motor clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(FORWARD);  //rotate the motor clockwise
}

void right()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(FORWARD); //rotate the motor clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(FORWARD); //rotate the motor clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(BACKWARD); //rotate the motor anti-clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(BACKWARD); //rotate the motor anti-clockwise
} 

void Stop()
{
  motor1.setSpeed(0); //Define minimum velocity
  motor1.run(RELEASE); //stop the motor when release the button
  motor2.setSpeed(0); //Define minimum velocity
  motor2.run(RELEASE); //rotate the motor clockwise
  motor3.setSpeed(0); //Define minimum velocity
  motor3.run(RELEASE); //stop the motor when release the button
  motor4.setSpeed(0); //Define minimum velocity
  motor4.run(RELEASE); //stop the motor when release the button
}

Comments

Post a Comment

Popular posts from this blog

IOT Based Heart Rate And SpO2 Tracker With NodeMCU MAX30100 And Blynk Application With Code Diagram

Circuit Diagram: SCL PIN - D1 , SDA PIN - D2 , INT PIN - D0 Code: #include <Wire.h> #include "MAX30100_PulseOximeter.h" #define BLYNK_PRINT Serial #include <Blynk.h> #include <ESP8266WiFi.h> #include <BlynkSimpleEsp8266.h> #include "Adafruit_GFX.h" #include "OakOLED.h" #define REPORTING_PERIOD_MS 1000 OakOLED oled; char auth[] = "*********************";             // Authentication Token Sent by Blynk char ssid[] = "********************";        //WiFi SSID char pass[] = "*********************";        //WiFi Password // Connections : SCL PIN - D1 , SDA PIN - D2 , INT PIN - D0 PulseOximeter pox; float BPM, SpO2; uint32_t tsLastReport = 0; const unsigned char bitmap [] PROGMEM = {   0x00, 0x00, 0x00, 0x00, 0x01, 0x80, 0x18, 0x00, 0x0f, 0xe0, 0x7f, 0x00, 0x3f, 0xf9, 0xff, 0xc0,   0x7f, 0xf9, 0xff, 0xc0, 0x7f, 0xff, 0xff, 0xe0, 0x7f, 0xff, 0xff, 0xe0, 0xff, 0xff, 0xff, 0xf0,  ...
3 comments
Read more

How To Make Wi-Fi Car With NodeMCU| NodeMCU Projects| Topped With Fun

Circuit Diagram:  Code: #define ENA   14           // Enable/speed motors Right        GPIO14(D5) #define ENB   12            // Enable/speed motors Left         GPIO12(D6) #define IN_1  15            // L298N in1 motors Right           GPIO15(D8) #define IN_2  13            // L298N in2 motors Right           GPIO13(D7) #define IN_3  2             // L298N in3 motors Left            GPIO2(D4) #define IN_4  0             // L298N in4 motors Left            GPIO0(D3) #include <ESP8266WiFi.h> #include <WiFiClient.h>  #include <ESP8266WebServer.h> String command;  ...
Post a Comment
Read more

Obstacle Avoiding Car With Ultrasonic Sensor|Autonomous Car Using L293D Motor Driver|Topped With Fun

Download The Libraries Here:- Motor-Shield-l-master Arduino-NewPing-master Circuit Diagram:- Code:- #include <AFMotor.h>   #include <NewPing.h> #include <Servo.h>  #define TRIG_PIN A4  #define ECHO_PIN A5 #define MAX_DISTANCE 200  #define MAX_SPEED 190 // sets speed of DC  motors #define MAX_SPEED_OFFSET 20 NewPing sonar(TRIG_PIN, ECHO_PIN, MAX_DISTANCE);  AF_DCMotor motor1(1, MOTOR12_1KHZ);  AF_DCMotor motor2(2, MOTOR12_1KHZ); AF_DCMotor motor3(3, MOTOR34_1KHZ); AF_DCMotor motor4(4, MOTOR34_1KHZ); Servo myservo;    boolean goesForward=false; int distance = 100; int speedSet = 0; void setup() {   myservo.attach(10);     myservo.write(115);    delay(2000);   distance = readPing();   delay(100);   distance = readPing();   delay(100);   distance = readPing();   delay(100);   distance = readPing();   delay(100); } void loop() {  int distanceR = 0; ...
Post a Comment
Read more